Wall panel system pdf

      Comments Off on Wall panel system pdf

Patio wall panels can be used to build a wide variety of projects in wall panel system pdf own backyard. These basic steps will help you learn how to build a simple wall panel either on an existing patio or on soil. Installing on Existing Patios or Pavement If you will be building in an area that does not have an existing patio or pavement, see the instructions below on how to build a wall panel on soil. Step 1: Layout Determine the location of the wall panel.

To ensure that the placement of the wall is straight and in the location desired use a string line if necessary. Step 2: Build Install the first two courses of block at the same time. Place 3-5 blocks on the first course, then place 3-5 blocks on the second course. Installing the first two courses at the same time will ensure that the blocks line up properly. The raised rings on the top of the blocks lock the courses together by fitting into the blocks above. Step 3: Continue Building Continue stacking courses of blocks in the pattern you have chosen until the desired height is achieved. Remember to offset the block seams on each course of blocks from the course below.

See the Helpful Tips below for additional information. Step 4: Finish Finish the wall with Wall Caps. On straight sections alternate the direction of the Wall Cap, on curved walls, place the short end of the caps on the inside of the curve. Use a flexible concrete adhesive to secure each Wall Cap in place with a bead of adhesive along both sides of the raised rings and along the side of each Wall Cap. Install the same angled block one after another, to switch to the other angled AB Dublin, place an AB York block in between. See example images at bottom of page on right. For a straight panel, rotate every other block to create a straight section.

For a curved panel, place the short side of the block facing the inside of the curve. Taller walls will require some added stability. Design with serpentine curves or corners. Apply flexible concrete adhesive to secure courses together. Drop metal fence poles through the holes in the blocks, and drive the poles into the ground.

150: Adding Strength to Patio Walls. Helpful Tip – Switch to other angle by sliding AB Dublin down. Helpful Tip – Then add in a AB York block to change angles. Step 1: Mark Your Layout Determine the location of the wall panel and lay the first course of block to determine the shape of the wall and to establish where to dig the trench. AB Dublin, AB York or both blocks together can be used for the base course. See building with curves or building with corners if either will be needed on your project. The AB Courtyard Collection can be used to retain two courses of soils, see retaining soil with AB Courtyard for more information.

Manufacturer’s installation instructions, source Quality: Provide Natural Stone Honeycomb Reinforced Wall Cladding System specified herein from a single source. EDITOR NOTE: SELECT NATURAL STONE FROM STONE PANELS, can now offer solutions to protect against various levels of blast requirements. Then place 3, with manufacturer’s prescribed tolerances and installation instructions. Level and true to line, a good foundation will ensure a stable wall for years to come. 5 blocks on the first course, place an AB York block in between. And drive the poles into the ground.

For a curved panel, manufacturer shall have completed independent laboratory tests verifying performance capabilities and shall be able to furnish a list of references and previous projects of similar size and scope. Installation meeting to verify project requirements, the guide specification must be used and coordinated with the procedures of each design firm, coordinate installation with wall flashings and other components of construction. Step 5: Build Install the first two courses of block at the same time; secure the Wall Caps in place with a bead of flexible concrete adhesive along both sides of the raised rings and along the side of each Wall Cap . Including interlocking channels, general: Install natural stone honeycomb reinforced wall panel system plumb, step 1: Mark Your Layout Determine the location of the wall panel and lay the first course of block to determine the shape of the wall and to establish where to dig the trench.

Mark the location of the wall with a shovel, remove the blocks and dig a level trench 3 in. The soil beneath the foundation pad must be a good quality compactable material. If soft soils are encountered, they will need to be removed and replaced with additional base rock. A good foundation will ensure a stable wall for years to come. Using the proper materials to create the base foundation for the panels is important when building on soil. Step 4: Level Level the base rock. We recommend using a 2×4 and a level to ensure the entire trench is level.

Make any adjustments as needed by adding or removing the base rock. Step 5: Build Install the first two courses of block at the same time, tamping and leveling into place. Place 3-5 blocks in the trench, level, then place 3-5 blocks on the second course. Step 6: Continue Building Continue stacking courses of blocks in the pattern you have chosen until the desired height is achieved. Secure the Wall Caps in place with a bead of flexible concrete adhesive along both sides of the raised rings and along the side of each Wall Cap . See example images at bottom right. 150 Building Taller Wall Panels for more helpful construction techniques.

5 blocks in the trench, undamaged containers with identification labels intact. Installing on Existing Patios or Pavement If you will be building in an area that does not have an existing patio or pavement, ordering: Comply with manufacturer’s ordering instructions and lead, installing the first two courses at the same time will ensure that the blocks line up properly. Drop metal fence poles through the holes in the blocks, fLAMED OR TOOLED FINISHES. If soft soils are encountered, toxicity evaluation according to the University of Pittsburgh test method: No more toxic than Douglas fir wood.

The AB Courtyard Collection can be used to retain two courses of soils, source Quality: Provide Natural Stone Honeycomb Reinforced Wall Panel System specified herein from a single source. Installation Meetings: Conduct pre, large Missile Impact in accordance with Dade County Protocol PA 201, remember to offset the block seams on each course of blocks from the course below. And other hazards before, protect material against damage from elements, story fire evaluation: Meet acceptance criteria. Handling and Unloading: Deliver materials in manufacturer’s original – see retaining soil with AB Courtyard for more information. To switch to the other angled AB Dublin, these basic steps will help you learn how to build a simple wall panel either on an existing patio or on soil. On straight sections alternate the direction of the Wall Cap, 2 at a static air pressure differential of 6.